Cel-Fi GO Repeater for Telstra Stationary Packs, Cel-Fi Repeater for 4G, Telstra 4G Booster, Mobile Phone Booster for 4GX, Legal Telstra Repeater, Repeater for Telstra

 

 

Home         The Company                 How Cel-Fi Works         Benefits of Cel-Fi       Apply
 


Home
 

Cel-Fi GO stationary for Telstra 3g & 4g

Cel-Fi GO Stationary Repeater has been tested, authorised and approved by Telstra for use on the Telstra Mobile Network.

Nextivity’s Cel-Fi GO is a one box indoor coverage solution for Telstra’s Next G® and 4GX networks operating on 3G 850Mhz or 4G 700/1800 bands. It is designed to dramatically boost voice quality and increase data speeds for in building applications.

The Cel-fi GO offers a more flexible installation over other Cel-Fi models due to the abilty to run cables to where the signal is needed most. By not having a wireless link between two boxes GO can operate in areas that are saturated with Wi-Fi.

Cel-Fi GO protects the mobile network in several ways by:

  • continuously monitoring power levels of the cell tower it is connected to and constantly adjusting the Cel-Fi’s output power to suit.
  • only amplifying and disbursing a particular carrier’s mobile signal, operating within a set frequency band.
  • not interfering with the carrier’s network or other users on the network.
  • having a unique installation process to eliminate feedback into the mobile network.Cel-Fi GO is covered by a 24 month warranty.

Important Note: Cel-Fi GO will boost a single band at a time (either 3G 850 or 4G 700 or 4G 1800). It is highly recommended to leave the GO in 3G mode to ensure voice calls are received. Voice on 4G (VoLTE) will only work in
selected areas and with l

Downloads

  Cel-Fi GO Stationary Brochure

  Cel-Fi GO Stationary Quick Start Guide

Supported Networks

Telstra, Aldi Mobile, Boost Mobile, Woolworths Mobile

 

Cel-Fi GO for Telstra

     GO STATIONARY MODEL

  For building and marine applications
  100dB of system gain
  Up to 900m² indoor coverage area
  Includes external and internal antennas
  Locked to Telstra’s Mobile Network
  Carrier approved
  Band Selection Button
  Bluetooth WAVE App for iPhone, Android & Computers

money-back-guarantee-30days
30 Day Money Back Guarantee*
If you are not 100% happy with the performance of this product
it can be returned within 30 days after purchasing for a full
refund minus any shipping charges… terms and conditions

cel-fi-go-telstra-repeater-for-cars

Cel-Fi GO STATIONARY PACKS

Cel-Fi GO Repeater for Telstra - Building Pack

Cel-Fi GO Repeater for Telstra - Marine Pack

Cel-Fi GO Repeater for Telstra - Caravan Pack

Easy Purchasing Procedure


STEP 1
– Complete the Application
As a regulatory requirement you first need to answer some simple questions and complete a registration form.
Apply for Cel-fi

STEP 2
– Place Your Order
Once you have completed your application you will need to place your order with Northern Communications who will ship your order usually on the same day.

Specifications

FREQUENCY

UMTS/3G 850 – Band 5
Uplink: 824 – 849 MHz, Downlink: 869 – 894 MHz
4G 700/1800 – Band 28 & 3
Uplink: 703 – 733 MHz, Downlink: 758 – 788 MHz
Uplink: 1710 – 1785 MHz, Downlink: 1805 – 1880 MHz
(Will only boost a single frequency at a time)

DATA

UMTS / HSPA / HSPA+/ LTE (FDD)

GAIN

Up to 100 dB system gain

BAND SELECTION

Button for band selection:
3G: 850
4G: 700 or 1800 (strongest signal)
AUTO: 850, 700 or 1800 (strongest signal)

NETWORK UNIT

H: 28mm
W: 87mm
L: 255mm
Weight: 600g

 

ENVIRONMENT
Operating Temperature: 0° to 65°C
Storage Temperature: -25° to 65°C
Relative Humidity: 0 to 95% noncondensing
POWER
12 VDC via external supply (2 included)
External Supply: 100-240 VAC, 47-63Hz
Power Consumption: <15W per unit
INTERFACES
External Antenna Ports: Donor and Service SMA Female
Programming Ports: Mini-USB
Bluetooth Low Energy
WARRANTY
24 months
CERTIFICATIONS

CE Mark
C-TICK
FCC
RCM

 

INSTALLATION

Cel-Fi GO is a state of the art, very complex “Smart Repeater” and is approved by Telstra if installed correctly.

It is guaranteed to provide massive signal enhancement in poor reception areas, however incorrect installation may significantly reduce
performance.

Installation of a Cel-Fi GO is best done by a qualified installer. Only qualified Powertec Telecommunication Resellers who have undertaken product training on the required precautions should perform installation of the Cel-Fi GO.

Vehicular Cel-Fi GO Packs in particular require you to take into account the vehicle’s safety mechanisms such as airbags, ABS, Traction Control, Stability Control and the auto electrics. Incorrect installation may result in water leaks, electrical failure, battery damage, fusing of internal wiring and cables or risk of FIRE. Misuse of this equipment could result in injury and equipment damage. In no event will Powertec Telecommunications P/L be responsible or liable for either indirect or consequential damage or injury that may result from the installation or use of this equipment.

If the above precautions are not fully understood, or if local conditions are not covered, contact your nearest Powertec Telecommunications sales or service representative for clarification.

You should also be familiar with applicable federal, state and local legislation and industry standards surrounding installations.

YOU SHOULD BE TRAINED IN HANDLING, INSTALLING, OPERATING AND MAINTAINING THE CEL-FI GO BEFORE YOU WORK ON ANY CEL-FI GO SYSTEM.

CEL-FI GO BLOG POSTS

GO to the NT
Thanks to staff at Centre For Appropriate Technology in Darwin for undertaking testing of Cel-Fi GO across outback NT. Great results achieved in some very remote communities.

Testing Different Antennas With Cel-Fi GO
During our GO testing we tested several different antenna types to see the effect this had on the boost and the final signal strength on the phone.

Installing GO in a Car
This article explains how to install Cel-Fi GO in a car, different setups and what performance you can expect.

The Cel-Fi GO Booster Models
If you are wondering why the Cel-Fi GO comes in two flavours, a ‘Stationary’ & ‘Mobile’ version, then this is the article you need to read.

Cel-Fi WAVE App
Cel-Fi WAVE offers a window into what is happening within the heart of a Cel-Fi smart booster. It also enables you to control certain features of the unit.

Cel-Fi GO – LED Indicators Explained
As Cel-Fi GO is only able to boost one frequency band at a time, a way of indicating and switching between frequency bands was developed by using a button. The button enables the selection of 3G, 4G/4GX or AUTO (band with strongest signal). An LED indicator displays which band GO is currently boosting.

Unboxing the Cel-Fi GO for boosting mobile phone signal in a car
Today we decided to unbox the Cel-Fi GO Mobile Version, the new repeater for boosting a mobile signal in a car.

*
30 Day Money Back Guarantee – Customer must return the Cel-Fi repeater within 30 days of receiving if the product does not perform to their expectations. Item must be returned with all packaging and parts in original condition. Refund component does not include any shipping charges paid.
* Telstra Approval – Customers must undertake an approval process to determine the product is suitable for their location. A Telstra approval form will need to be completed and signed by the customer.

® is a registered trade mark of Telstra Corporation Limited. ABN 33 051 775 556